Knowledge Base

 
Reset Search
 

 

Article

NCOS: How to Configure a capable Cradlepoint as a Wired and Wireless access point

« Go Back

Information

 
Content

NCOS: Configure a capable Cradlepoint as a Wired and Wireless access point

Products Supported: AER3100, AER2100, MBR1400v2, MBR1400, IBR600, and IBR1100. Click here to identify your router.

NCOS Version: 6.0 - for information on upgrading NCOS Versions, click here.


Quick Links

Summary

Configuration

Related Articles


Summary

Series 3 Cradlepoint devices normally operate as a NAT router, allowing computers connected to the LAN to use the Internet connection provided by the WAN interface. As a NAT router, the Cradlepoint is responsible for providing DHCP and local gateway access to connected clients.

If your existing network already has a DHCP server and local gateway configured, it is possible to reconfigure the Cradlepoint to act as a wired LAN client to that router. This turns the Cradlepoint into a wired switch/wireless access point for that existing DHCP server and local gateway. Set up this way, any wired or wireless computer connected to the Cradlepoint will get an IP address from the existing DHCP server and route traffic through its local gateway.


Configuration

Configuration Difficulty: Beginner

These examples will show you how to reconfigure a Series 3 Cradlepoint router to be used as a wired switch and wireless gateway to connect to another "Primary Router" DHCP server and local gateway in your network.

For example, assume there is already an existing wired Primary Router using local IP address 192.168.0.1 with subnet mask 255.255.255.0. This is the router that is providing DHCP services and providing local gateway access. The Cradlepoint will be configured as a LAN client for the Primary Router.

To begin, first make sure that the Cradlepoint is not connected to the other router.

  • Step 1: Log into the router's NCOS Page. For help with logging in please click here.
  • Step 2: Click on Networking then VLAN Interfaces from the navigation menu.

          User-added image

  • Step 3: Select the WAN row and click Edit.

          User-added image

  • Step 4: Select the Ethernet WAN port, click Remove and then Save.

          User-added image

  • Step 5: Under VLAN Interfaces click on the LAN row and then click Edit.
  • Step 6: In the Edit lan window click the Add button.
  • Step 7: Select Port 0(Ethernet WAN), leave the Mode as Untagged and click Update
  • Step 8: Click Save to submit the changes.

         User-added image

  • Step 9: Click on Local Networks and then Local IP Networks from the navigation menu.

          User-added image

  • Step 10: Select the Primary LAN and click the Edit button.
  • Step 11: Select the IPv4 Settings tab.
  • Step 12: Set the IP Address to 192.168.0.2 and the Routing Mode to Standard.
    • Note: This address is for this example only. Your network may have a different address range. The Cradlepoint's IP address should be on the same network as your primary router.

          User-added image

  • Step 13: Select the IPv4 DHCP tab.
  • Step 14: Remove the checkmark next to DHCP Server and click Save.

          User-added image

  • Step 15: Attach an Ethernet cable from a LAN port on your Primary Router into any of the Cradlepoint's Ethernet ports.
    • Note: We suggest using the Cradlepoint's WAN port for this connection as it retains a logical port usage to easily determine which cables are connected to which devices.
  • Step 16: You may need to refresh your computer's IP address, or else reboot the computer or Cradlepoint, in order to get a new IP from the Primary Router.

After making this change, the Cradlepoint will no longer be performing any routing functionality, but instead will act as a wired switch and wireless access point to extend your existing network. All DHCP, gateway, and routing functionality will be handled by the Primary Router.

Any computers wired or wirelessly connected into the Cradlepoint will receive IP addresses from the Primary Router (beginning with 192.168.0.X in our example). Any computer attached to that network should also be able to access the Cradlepoint from the LAN IP address you specified (192.168.0.2 in our example).

Note: It may be useful to change the Cradlepoint's wireless SSID and password to match the same credentials as your other router uses. This would allow nearby computers with the Primary Network's wireless credentials to be able to connect to whichever network has a stronger signal.

To undo this configuration you can either follow the directions in reverse order, or you can perform a factory reset on the device.


Related Articles/Links


Published Date: 07/14/2017

This article not have what you need?  Not find what you were looking for?  Think this article can be improved?  Please let us know at suggestions@cradlepoint.com

Feedback

 

Was this article helpful?


   

Feedback

Please tell us how we can make this article more useful.

Characters Remaining: 255