Category     

AER2100 Manual: Quick Start

« Go Back

Information

 
Content

Quick Start


 

Basic Setup


1. Insert an activated SIM.

A wireless broadband data plan must be added to your Cradlepoint AER2100. Wireless broadband data plans are available from wireless carriers such as Verizon, AT&T, Sprint, EE, and Vodafone. The SIM must be provisioned with the carrier. Contact your carrier for details about selecting a data plan and about the process for provisioning your SIM.

Once you have an activated SIM, insert it into the integrated modem. Insert the SIM card into the slot marked SIM 1 (use the other slot, SIM 2, for a secondary/backup SIM).

image

Be sure to insert the card with the notch-end first and the gold contacts facing down – it will click into place.

image

2. Attach the integrated modem.

Follow these steps to attach the integrated modem:

1) Remove the left side panel cover from the router. Use a Phillips screwdriver to remove the screws, and use the Multipurpose Retaining Tool (included in the router package) to remove the cover.

image

2) Slide the modem into the side of the router. The protruding section of the green board fits into the groove.

image

3) Reattach the panel cover and screw it back on. (When necessary, remove the cover and modem using the Multipurpose Retaining Tool.)

3. Attach the WiFi and modem antennas.

Attach the three WiFi antennas (included) and two modem antennas to the connectors. Antennas are jointed, which enables you to position them for optimal signal. To attach, hold the antenna straight and twist the base of the antenna to connect, folding the joint if needed.

Examples of suggested antenna orientations:

Desk Mount

image

Wall Mount

image

Care should be taken to ensure that the router antennas are not near metal or other RF reflective surfaces.

4. Connect the power source.

Plug the provided power supply (12V DC wall adapter) into an electrical outlet. Then connect the power supply to the router.

image

Ensure power is switched on:

  • O = OFF
  • I = ON

When you set the power switch to the ON ( I ) position, watch for the power LED to illuminate.

If you would like to secure the power supply cord, attach the Multipurpose Retaining Tool as shown below. Secure with included screws.

image

5. Connect to a computer or other network equipment.

Connect wirelessly to the WiFi broadcast or with an Ethernet cable connected to your computer and then plugged into one of the Ethernet LAN ports (numbered 1–4).

The default WiFi network name broadcast is “2100-xxx”, where “xxx” is the last three characters of your router’s MAC address (this is the SSID on the product label). To connect to the WiFi, you will need to input the DEFAULT PASSWORD when prompted. The DEFAULT PASSWORD is provided on the product label found on the bottom of your router.

NOTE: The product label below is an example only: your DEFAULT PASSWORD and SSID will be unique.

image

 

Accessing the Administration Pages


Once you are connected, open the Cradlepoint AER2100’s GUI-based administration pages to make configuration changes to your router.

  1. Open a browser window and type “cp/” or “192.168.0.1” in the address bar. Press ENTER/RETURN.
  2. When prompted for your password, type the eight character DEFAULT PASSWORD found on the product label.

image

It's possible – and more efficient – to do all your configuration changes through Cradlepoint NetCloud Manager (NCM) without logging into the local administration pages. Set up a group of routers and set the configuration for all of them at once. See below for more information about NCM.

 

First Time Setup Wizard


When you log in for the first time, you will be automatically directed to the FIRST TIME SETUP WIZARD, which will walk you through the steps to customize your Cradlepoint AER2100. You have the ability to configure any of the following:

  • Administrator Password
  • Time Zone
  • WiFi Network Name
  • Security Mode
  • Access Point Name (APN) for SIM-based modems
  • Modem Authentication
  • Failure Check

If you are currently using the router’s WiFi network, you will need to reconnect your devices to the network using the newly established wireless network name and password.

NOTE: To return to the First Time Setup Wizard after your initial login, select GETTING STARTED on the top navigation bar and FIRST TIME SETUP in the dropdown menu.

 

Using NetCloud Manager


Rapidly deploy and dynamically manage networks at geographically distributed stores and branch locations with NetCloud Manager, Cradlepoint’s next generation management and application platform. NetCloud Manager (NCM) integrates cloud management with your Cradlepoint devices to improve productivity, increase reliability, reduce costs, and enhance the intelligence of your network and business operations.

Click here to sign up for a free 30-day NCM trial.

1445_NCM_img001.png

Depending on your ordering process, your devices may have already been bulk-loaded into NCM. If so, simply log in at cradlepointecm.com using your NCM credentials and begin managing your devices seamlessly from the cloud.

1445_NCM_img002.png

If your device has not yet been loaded into your NCM account, you need to register. Log into the device administration pages and go to Getting Started → NetCloud Manager Registration. Enter your NCM username and password, and click on “Register”.

1445_NCM_img003.png

Once you have registered your device, go to cradlepointecm.com and log in using your NCM credentials.

For more information about how to use Cradlepoint NetCloud Manager, see the following:

This article not have what you need?  Not find what you were looking for?  Think this article can be improved?  Please let us know at suggestions@cradlepoint.com
 

 
Knowledge Home | Product